Pump VAZ-2110: device and replacement

Pump is one of the most important and irreplaceableparts, which is installed absolutely on all modern cars. This element is a pump that provides forced circulation of antifreeze in the engine cooling system (SOD).

On the machines of the VAZ of the tenth "family", it happensexclusively closed type, with forced circulation. And today we will consider how to correctly change the pump to VAZ-2110, and also learn its device.

Feature of the element

In the automotive world, there are twoa variety of pumps coolant - with a mechanical or electric drive. In the first case the drive is carried out from the distributor or crankshaft of the internal combustion engine using a belt transmission. In the case of the electric one, all this is done by one electric motor, which has its own control system. Regardless of the type and dimensions of the machine, this pump is installed only in the front of the engine. VAZ-2110 is no exception.

The device of this part assumes the presencea centrifugal pump. In addition, the design of this element includes the impeller and housing. The first part is most often mounted on a shaft with a pulley. The body can be either cast iron or aluminum. It has special channels for drawing and removing the antifreeze to the impeller. A gasket is placed between the pump housing and the engine cylinder assembly. It does not allow the coolant to flow out of the pump.

Working wheel

The impeller, or impeller, is one of thethe most important elements of the pump, ensuring the circulation of antifreeze in the system. This part is a set of blades of a special shape and is mounted on the drive shaft. The latter is located in the housing on bearings. The drive pulley is located on the opposite side of the shaft.

Replacement and installation of the pump (VAZ-2110 and 2112)

Let's start with the dismantling. First of all, remove the wire from the negative battery terminal. Then drain the coolant from the car. For convenience, you can remove the adsorber. It is dismantled without touching the wires and hoses. Then we remove the covers from the engine and install the piston I of the cylinder in the position of the top dead center (that is, when the compression stroke should take place).

Then take the jack and lift the front of the car. We remove the right wheel. Further we take out rollers and a pulley of a cam-shaft. This is done as follows:

1. First we loosen the tension rollers, then theyare removed together with the timing belt. Be careful! After this, you do not need to turn the crankshaft and camshaft, as the piston can hit the valves.

2. Unscrew the camshaft gear. Pay attention to the fragility of the teeth.

3. We dismantle the pulley.

In the next step, remove the plastic coverpumps. Since one of his mounting bolts is at the bottom, you have to climb under the car. Then a pump will appear before our eyes. VAZ-2110, fortunately, is easy to maintain, so removing the coolant pump will not be difficult. First remove the three mounting hexahedrons. Further under the pump of a cooling liquid container is put. It will be useful to us when removing the element, since here the leakage of antifreeze will be inevitable.

What do I need to know when installing?

Everything from our car was successfully extractedold pump. The VAZ-2110 is further manned with a new part. You can do it without any special tools. In principle, the installation of the pump (VAZ-2110, 2112) is performed in the reverse order, similar to the removal, but here it is necessary to note several important points.

First, the new part must containgrease. Often she is already present there. But if it's not there, be sure to lubricate the element. Secondly, if the pump VAZ 2110-th model has a paper gasket, we put on it a sealant and wait for 10-15 minutes, until it dries. After you can install the part in place.

Why do I need an additional pump on the VAZ-2110?

Very often owners of domestic carsAsk about installing an additional coolant pump. As a result of the operation of two pumps, it is possible to significantly increase the efficiency of the heater at idle speed of the engine. And if before that the stove blew at 1000 rpm only with warm air, then after the upgrade to the salon there will already be a hot flow. In addition, when moving in the coolant system, the pump will ensure good circulation, which could not be achieved with a single pump.

Particularly important is the installation of an additional pumpcooling fluid for car owners living in the northern latitudes, where there is a significant shortage of power of the stove at an ambient temperature of minus 20-25 degrees Celsius.

And because our cars are not capable of normalto heat up the cabin in this winter, the installation of a second pump is the only effective way to improve the situation. By the way, this technology has long been practiced on cars BMW and Mercedes. So with an additional pump your iron friend will be one step closer to a foreign car.

So, we found out how the pump is dismantled. VAZ-2110 and its "brethren" models 2111 and 2112 have a similar design of the coolant system, so this instruction is relevant for all vehicles of this family.

</ p>