Ball support "Lada Largus": description, possible malfunctions, replacement. Restoring ball bearings

"Lada Largus" is a Russian station wagon,built on the basis of the "Renault Logan". The car is serially produced from 2012. The station wagon has a classic suspension scheme, where the front stands "McPherson". To implement the rotation of the wheel in the design, a ball bearing is also provided. "Lada Largus" is equipped with this element in the upper and lower part of the hub. What is this detail, what are its malfunctions and how to replace it with your own hands? All this you will learn in our today's article.

Characteristic

An integral element of the chassis of the car"Lada Largus" is a ball bearing. This part is the link between the steered wheel and the triangular suspension arm. The element helps to turn the hub in different positions. The part itself has a conical shape with a ball tip (where from and so specific name), which simultaneously swings and rotates. Thus, the spherical support of "Lada Largus" ensures the rotation of the hub, keeping the wheel itself in the horizontal plane. In this case, the disk can move freely in an upright position (when the machine hits a pit or any other irregularity).

Possible malfunctions

In 90 percent of cases, the cause of the failureThe ball joint consists of a leaky anther. It is a small piece of rubber, covering the junction. Over time, the dust cover cracks and crackles. As a result, water and dirt get inside, acting like an abrasive. Also in the support are formed and corrosion processes, which significantly reduce its resource.

The next cause of the malfunction is naturalwear. The service life of the ball joint "Lada Largus" with a lateral groove is from 150 thousand kilometers. It is a very reliable and hardy knot. But over time, it loses its strength. The part is assigned to the load from the entire vehicle. It is at this point that the entire mass of the machine is concentrated (at least, its front part). At the junction of the joint joint, the element may break (especially if the quality of the pavement leaves much to be desired). Also, in the places of joining the surfaces, a generation is formed. This increases the clearance between the body of the part and the finger. As a result, the spherical support of "Lada Largus" ceases to hold the wheel in the horizontal plane.

Instruments

To perform the operation to replace this part we will need:

• Balonnik.
• Jack.
• Torque wrench.
• A thick slotted screwdriver and a small hammer.
• Horn keys, as well as the head "for 16", "for 18".

Getting Started

So, how is the ball bearing "LadaLargus? " First we need to loosen the bolts of the wheel (if there are "secrets", unscrew them). Next, hang out the front of the car, using a jack. After that, detach the rod of the stabilizer bar. If there is metal protection of the engine, we remove it.

Then, using the head "for 16" unscrewnut of the bolt, which pulls the ball ball with a pivot. On the other hand, hold the bolt with a key of the same diameter. We take the element out. Now we need to unhook the joint of the support finger and the pivot. It is not easy to do this - you need a powerful minus screwdriver (you can also knock out the bolt "by 16" if it is stuck in the grooves). Then we remove the ball from the hole of the fist. Be attentive - the detail may not succumb. Therefore, at the same time, we swing the pivoting fist, holding on to the brake disc.

As further replacement of a spherical support on"Lada Largus" with their own hands? At the next stage, unscrew the nut of the rear bolt of the suspension arm. We will need a head with a ratchet "for 18", as well as a car key of the same size. Last, we will keep the part from turning (as in the previous case). Then we take the bolt out. If it is tight, knock out with a slotted screwdriver. Now you can safely remove the lever out. But that is not all.

Remove the support from the lever

Now, when the element is removed from the car,we proceed to disassemble it. Using a screwdriver, we support the support for the shoulder. Extrude the ball from the lever, leaning on its edge. Next, look at the state of the element itself. The hole in the lever should not have cracks or any ruptures. If everything is in order, we clean it of dirt with rags soaked in gasoline or white spirit, and proceed to press the new support.

For this we need to insert the part into the hole andPut a piece of pipe of suitable diameter under the lever. With light strokes of the hammer we press the element into the grooves. Take care that there is no distortion. After that, the lever assembly with the ball can be installed into place. The assembly procedure is carried out in the same way in the reverse order.

Tightening torques

When assembling, it is important to tighten all the screws correctly. So, the nuts of fastening the silent blocks of the lever are tightened with a force of 105 Nm. Connecting rod - 21 Nm. The bolt that pulls the swivel fist and ball is tightened with an effort of 62 Nm.

note

After successful replacement of the ball joint, be sure to go through the adjustment procedure of the camber-toe.

The angles of the position of the wheels after repair can change, which will cause uneven wear and tear of the machine to the side.

Repair parts or recovery?

Ball joints are subject to repair only in the case ofsmall output. But it's hard to do it yourself. The cost of restoring the spherical supports to the SRT is about a thousand rubles. Plus removal and installation - 1400 rubles. Proceeding from this, a more correct decision will be the purchase and installation of a new ball bearing on "Lada Largus".

The price of one element is 850 rubles (the original from "Renault"). The cost of the part with a side groove (a kind of analog) is 620 rubles.

Conclusion

Ball joint is a very important element inconstruction of any car. From his condition, without exaggeration, riding safety depends. After all the worn out ball can simply jump out of fastenings, and the wheel will come off outside. At high speed this can lead to serious consequences. Therefore, it is necessary not to ignore the problem and to diagnose the element at the first deaf impulses of the suspension. The wheel should not play when the car is on a lift or jack.

</ p>