Indesit does not turn on: what should I do? Causes

Indesit washing machinesare of good quality. However, they have certain drawbacks. First of all, it should be noted that many machines wear out a belt quickly. Filters need periodic cleaning. Some owners say that the engine can burn out. At the same time, belt drives fail.

If the Indesit washing machine does not turn on,the causes of breakdown can always be determined independently. Modern devices are manufactured with a display, and a malfunction code is displayed on it. It is much more difficult to fix the problem.

Models Indesit Wisl 103

These models are manufactured with a simple belttransmission. If the washing machine Indesit Wisl 103 turns on with an error, experts advise first of all to inspect its motor. To do this, remove the model panel and unscrew the protective plate. The motor in this case is located at the bottom of the device. Next, the stops on which the part is located are removed. In order to disconnect the motor, it will be necessary to disconnect all the wires. To diagnose this element, it is better to contact the service center.

Repair Indesit Iwsc 5085

This model has a fairly narrow drainhose. If the Indesit Iwsc 5085 does not turn on and the water does not enter the tank, it is recommended to check the nozzle. For this, the model needs to be turned back. It is important to immediately disconnect the device from the network and the water supply system. To block the water, you need to use a wrench. Further it is necessary to clean a branch pipe. To do this, you can use a regular rag.

If the integrity of the tube is broken, then it willreplace. Also it is worth noting that problems can often be in the filter. The specified part is at the bottom of this model. To clean the filter, you can use a small stick. Still need a little cotton wool.

Model Indesit Wite 107

This model is produced with a high-quality motor. However, it installs a small transmission unit. This device operates from the modulator. If the Indesit Wite 107 does not turn on and the display shows A2, then the unit is out of order. To inspect and repair this element, you need to open the lid of the washing machine. Further it is recommended to inspect the motor carefully.

If it is not visible on the darkening, then the problemis in the gearbox. In order to remove it, you have to unscrew the gearbox model. It is located in the washing machine next to the motor, and is attached to the nuts. Thus, the part can be twisted with a small screwdriver. The next step is to get the gearbox directly. Then it must be inspected for defects. As a rule, when the model is overloaded, the contacts burn out. The cause of this failure is caused by network failures. To correct this type of fault, the transmission unit must be replaced at the service center.

Breakage Indesit Wise 10

This model works from a contact rotor. The motor in this case very rarely breaks. When the rotor breaks down, the model displays A3 error. If the washing machine Indesit Wise 10 does not turn on, experts advise to inspect the unit, as well as the gearbox. To do this, the model cover is removed and the integrity of the module is checked. Then you can do the gearbox. In this washing machine it is located under the cover of the rotor.

Remove the gearbox using a key. Further, the integrity of its plate is checked, and the upper part of the part is inspected. Sometimes it appears plaque. This is due to water leaks. If the rotor refuses to start after cleaning, you can simply replace the device. To do this, it is enough to know its labeling and contact the service center. You can place the part by yourself. The main thing - during installation, do not damage the motor wiring.

Model Indesit Wil102X

This model is famous for a good gearbox andquality drum. Some customers complain that the device often breaks the water level sensor. When this happens, the display shows A5. If the Indesit Wil102X does not turn on, then the sensor needs to be changed. In this case, you have to completely remove the drum model. However, the lid is first detached. The next step is to remove the protective harness, which is located near the drum. Next, you need to twist the head from the central rod. You can do it by hand. The drum is difficult to shoot to one person. In this case it is better to ask for help from a friend.

Further under the module you can see a smalla box that is a sensor. The element is fixed to the body with two bolts. When twisting an element, it is important not to damage the wiring. After detaching the sensor, it must be inspected and the seal checked. When the overlay is erased, the body of the element begins to flow through the water. All this suggests that the sensor will have to buy a new one.

Repair Indesit Wisn 101

This model has many advantages. However, users note a weak tourniquet that is mounted on the drum. If, for this reason, the Indesit Wisn 101 washing machine does not turn on, the display shows A6. To repair the model yourself, you will have to prepare the necessary tools. First of all it is recommended to choose a set of screwdrivers. Also need a large key for the stem head. To start the repair, the lid of the washing machine is removed, which is located on the back panel. The next step is to disconnect the rotor box.

If this is not done, the stock will be difficult to twist. In order to disconnect the rotor, you have to use the key. The next step is to unscrew the stem directly. The sheep must be disconnected by hand. It is important to fix the protective harness. If the tape on it is cracked, then it needs to be replaced. To do this, you need to know the diameter of the bundle, which is indicated on the outside. After that, you can put the drum in place and install the rotor.

Motor breakdowns

Motors very rarely break down in washing machinescompany Indesit. However, there are such cases. The models of the last series display error B3. The cause of the breakdown is most often covered by the heavy workload of the device. At high revs, the motor heats up. If long erase, then it can not withstand the load. When the Indesit washing machine does not turn on, you need to inspect the part. If the adapter has blown on the motor, then it will have to be completely changed. The cost of the part depends on the model series.

Causes of the breakdown of the tachodchik

When the Indesit washing machine does not turn on, andthe E3 code is displayed, then the sensor has stopped working. The cause of this type of failure is the overheating of the capacitor. This happens most often because of network failures. If necessary, you can change the Tadget yourself. Before this, the washing machine must be disconnected from the mains.

The next step is to unscrew the nuts on the backcover the model. After that, the protective plate of the module is removed, which is located in the upper part of the washing machine. In order to get the device, you need a screwdriver. In the models of the last series, this element is fixed on two screws. After disconnecting the device, the bottom of the box is inspected. When the element overheats, it often darkens, an unpleasant smell is felt. In this situation, the sensor will have to be replaced. After this, it is necessary to reinstall the protective plate and fix the lid of the washing machine.

Temperature sensor errors

Temperature sensors rarely breakmodels. If the inscription B1 is visible on the display, and the Indesit washing machine does not turn on, then the problem lies in this element. First of all, we need to understand the reasons for the sensor failure. Experts say that it is out of order because of dirty water. Also, the problem may be the wear of the relay. To independently inspect the element, you will have to completely twist the module. For this purpose, the lid is removed, as well as the protective plate. Next, you will first need to inspect the module. Experts recommend checking the part with a tester.

When the resistance is more than50 Ohm, the problem lies in this component. If the testing of the module was unsuccessful, and the Indesit washing machine does not turn on, then it is necessary to check the sensor directly. At many models it is behind an output branch pipe, and it is fixed on a rack. It leaves a small contact that connects to the board. To detach the element, it is important to carefully inspect the attachment of the device. In the models of the last series, the sensor is fixed on one clamp.

Causes of the failure of the level sensor

Sometimes washing machines break down sensorslevel. These elements fail because of the failure of the module. Also, the cause of the breakdown may be overload in the network. Level sensors are not repairable, but they can be changed. To this end, you need to make sure that the elements are broken. To do this, the lid is removed from the washing machine, and the drum is inspected. Level sensors are located under the plate, and connect to it through the contacts. If the tester shows a zero value, then the device is broken. It must be changed.