Shredders of food waste for the shell: overview, types, connection, repair

Food shredder for the shell, thoughgain popularity, but still are not an indispensable attribute in the kitchen. With this device, you can reduce the amount of dry debris by sending all the leftovers to the sink. In this case, there will be no unpleasant odors, crumbs, which could attract cockroaches. But there is such a device quite expensive, therefore, it is necessary to approach the choice of the disposer responsibly.

Varieties of shredders

Before making a choice, it takesDetermine what kind of apparatus is needed in the kitchen. Everything will depend on the principle of work, on which the dispouzers are divided into electrical and mechanical. The latter work from water, which affects the pressure on a certain number of knives. They contribute to the shredding of garbage, which is then sent to the sewage system. Mechanical food shredders for the shell can be called perfectly safe, since the blades are at a certain distance from the drain hole.

Mechanical chopper

As for the electric chopper, itworks on a different principle: it must be included as necessary. Inside the device there are no knives, and rubbish is crushed with special hammers. For the reason that the blade is missing, there is no risk of injury. The only drawback is a sufficiently high noise level. Among other things, such devices are inferior in efficiency to mechanical analogues. This is expressed in the fact that not all food waste can be recycled.

Recommendations for connection

If you are interested in food shredderswaste for the sink, then after the purchase, it makes sense to save money by trying to install the device yourself. These works are carried out in several stages, the first is the need to turn off the water and disconnect the sewer system from the sink. Rubber gasket will need to be located on the flange, and then connect the attachment of the new device to the sink, turning off the device itself.

When food shredders are installedwaste to the sink, one end of the drain pipe must be connected to the dispouter, while the other to the sewage pipe. The electric cord should be pulled to the socket, the latter must be grounded. It is important to look at the equipment passport before carrying out the work, as some manufacturers recommend using a separate line during installation. At the final stage, you can test the device by turning on cold water and using the "Start" button. Putting food waste into the sink, you will be able to make sure that the device is working properly.

Feedback on the operation

Users argue that some models,presented for sale, are deprived of a separate switch. They work on the principle of batch loading. Once the tank is filled with waste, you need to rotate the throat cover. It is inserted into the drain hole in the sink and acts as a switch. As the buyers emphasize, if you are not satisfied with such a design of the dispositor, it is important to pay special attention to the purchase of the functional.

Repairing the Dispositor

If you decide to purchase a food shredderwaste for the sink, reviews of which are mostly positive, it must be remembered that, whatever it is, it is impossible with 100% probability to exclude the possibility of breakage. If nevertheless there was a necessity to remove the device, repair should be started from a visual inspection, for which the equipment is disconnected from the network. After that, the master is recommended to use the flashlight to look inside the working chamber. At the same time, the rubber petals are bent by hand.

If the visual inspection did not allowresults, it is necessary to use a special end rod, which should be inserted into the hole of the corresponding shape, which is located under the bottom of the engine compartment. You can find this element in the central part of the case. The master must try to rotate the shaft, after which you can try to turn on the chopper, but there is a chance that the working capacity will be restored.

Nuances of repair work

Interested in a food waste shredder forsinks? How to choose such a device correctly? First of all, you need to decide whether you are prepared for the fact that electricity bills will increase. If not, it is best to prefer a mechanical model.

In the event that the electricaldisposer - its engine does not move when you press the "Start" button - it is important to pay attention to the fact that you should hear a slight buzz, which indicates the current flow through the windings. The absence of sound indicates that there is an overload protection inside. It can be about overheating. The master can check the integrity of the thermal fuse with a tester. If the disk is jammed, the device should be disconnected, otherwise the heating of the windings will be so strong that the equipment will finally fail.

If the food shredder has broken downsinks, you can repair it yourself, of course, without turning to a service shop. So, for example, the check of the stuffing boxes and their tightness can be carried out by each user, however for this purpose it is necessary to disassemble the case.

In addition, it is worth remembering that exploitingequipment without seals is not allowed. Water may be trapped inside, causing a short circuit. In this case, experts advise connecting the disposers with a differential protection device. The leakage current will increase, which will trigger the mechanism. From the negative consequences will save conventional plugs on the shield or thermal fuses. Among other things, the differential protection device will be an additional guarantee that no one will be shocked.

Overview of the Hankel FCB 901D food shredder

This food waste shredder for the sink,the price of which is 190 dollars, has a diameter of 159 millimeters. The device is equipped with a pneumatic switch, and the material of the crushing chamber is stainless steel. The engine is capable of the maximum number of revolutions, which is 3300 per minute. The capacity of the equipment is equivalent to 750 watts. The advantage is the possibility of continuous loading of food waste.

Reviews about the Dispenser Weissgauff ISE660

If you decide to choose an electric chopperfood waste for a shell, the connection of which is carried out according to the principle described above, then the above-mentioned model can be preferred. Buyers say that this device has an average cost of $ 219. All other characteristics are successfully combined with an affordable price. The volume of the crushing chamber is 0.6 liters, but the diameter of the device is 121 millimeters. Consumers choose this model also for the reason that it provides the possibility of continuous loading of garbage.