Crafts: how to make claws lynx from paper

Fantasy manifests itself in different ways and ideas. If you are looking for an answer to the question of how to make the lynx claws from paper, then for certain decided to surprise others with something original.

In the style of origami

Origami is a special technique of folding paper. To some, many origami-style crafts seem difficult to manufacture, but they are not. How fast to make claws from paper? The scheme of the craft is given below.

To produce one sheet in formatA4. First, you need to make a crease, in which a square is obtained from a rectangular sheet. Lower corners slightly bend. Bend it in half and again. Next, we fold the left half of the strip. Turn the given piece to the left. We put the sticking corner into the hole.

In order for the finger to freely enter the hole, it must be made more voluminous. It remains to make 9 more claws on the other fingers.

Paper lynx claws: phased implementation

How to make lynx claws from paper for a girl? Simply and easily. It is important to follow the description below.

It is desirable to prepare a sheet of A4 paper: we place it vertically.

1. The right corner should be wrapped so that a rectangle is obtained.
2. The lower corner is bent upward to get a five-cornered shape or a pentagon.
3. The opposite side is bent.
4. Then the part is folded diagonally, resulting in a triangle.
5. The figure turns to the left and the left edge is bent twice.
6. The right part needs to wrap the left one.
7. In the same direction, another bend is made.
8. In order for the claw to keep its shape, you need to bend one corner inside.
9. A hole for the finger should be slightly spread out for the convenience of entry.

So we answered the question of how to make paper claws for a girl. As you can see, this is not too difficult.

Naturally, this is not the only information on how to make the paper claws of a lynx or other predatory animal. There are other ways.

Complicated variant

How to make lice from the cardboard? As well as paper, although it should be noted that it can be quite difficult (the cardboard is difficult to bend and give the product the desired shape). Although you can try it if you want. But there are plenty of ways to produce paper claws. Above we described the simplest variants, and now we will present a complicated one. It is necessary to stock up the following tools:

• scissors;
• with a simple pencil;
• black gloves;
• glue-gun;
• A balloon with a black or gray paint;
• sheets of thick paper.

The two previous schemes show small claws. And how to make lynx claws from a larger paper?

1. We put the paper sheet in a triangle, and on itdraw the faces of another triangle and cut it out. The resulting figure is applied to the thick paper and we circle. Cut out the contour and turn off the cone.
2. On the cone draw two lines along the diagonal, which must then be cut. It turns out three identical parts, which need to be inserted at an angle to each other. Parts are glued together.
3. If it is a cat's claw, then they are ready. You can put them on your fingers. The size of the claw can be adjusted, it is sufficient to slightly cut the ends of the parts. Longer claws can be obtained by means of an elongation.
4. Very original look colored nails. In this case, you can make a painting of the craft. Suitable acrylic paint from the can. Lovely cat's claws ready!

Good advice

We presented several options for how to make the lynx claws from paper. Before starting to manufacture, you need to read the following tips:

1. You can make claws from ordinary white paper or cardboard, and for the original crafts, colored sheets will do.
2. It is important to observe the correct sequence in the process of making claws. Instructions are given so that the article remains motile and natural.
3. The length of the claws can be adjusted according to thefrom the desire: one can be worn on the other, but in this case it is necessary to glue them together for convenience and retention of the form. To remove the length, it is necessary to prune all parts of the claws.
4. In order to keep the crafts as long as possible, it is desirable to fasten the parts with glue. Do not abuse it, from excessive amount of claws will not look natural.