Water heater "Termex" (80 liters): instructions for use. The scheme

Water heater "Termex" (80 liters), instructionon the application of which will be described below, is manufactured using modern technologies, high quality materials are used in this process. Such devices have tripping protection, which provides electrical safety during operation. This equipment can be used to provide hot water to industrial and household facilities that have cold water pipes. The system should maintain a pressure, the level of which is from 0.05 to 0.6 MPa. The device should be used in heated indoor areas. The device must not be operated in continuous-flow mode.

User's manual

If you decide to choose a water heater "Termex"(80 liters), the instruction manual of which will tell you how to extend the life of the device, you should be aware that the models are presented for sale with mechanical and electronic control. In the first case, the keys on the external panel are responsible for selecting the power. By using both, you will provide a power equal to 2 kilowatts. This will ensure the needs, based on the amount of hot water that needs to be obtained.

When using a heater, you canAdjust the temperature using the toggle switch located on the control panel. Turning it counter-clockwise until it stops, you disconnect the water heater from the mains. If you turn the knob clockwise, you can increase the coolant temperature to 75 degrees.

Using a model with electronic control

Water heater "Termex" (80 liters), instructionon the application of which comes complete with the device, can have electronic control. In this case, you can enable or disable the left button, which is located on the panel. The display will show the heating temperature, and after 2.5 seconds you will be able to see the current water temperature in the heater. If you need to change the temperature of the water heating, when there is a model with electronic control, you can use one of three touch keys.

Different modes of operation

Water heater "Termex" (80 liters), instructionthe use of which will allow you to perform the installation yourself, can work in one of several modes. At the first power-up or after a power outage, a temperature of 75 degrees is set. If we are talking about models with an electronic panel or a digital sensor, then after a power outage the equipment goes into the "Demo" mode, which assumes a demonstration mode. The heating elements will not be switched on.

Storage electric water heaters"Termix" can be withdrawn from the demo mode by simultaneously pressing and holding the keys that are located on the control panel for 5 seconds and denote movement up and down. The device can go into standby mode, it is accompanied by a flashing company logo, and the indicator indicates the level of the water temperature in the heater.

Device of protective shutdown during operation

Operation of the water heater "Termex" canthe protective device trips. In order to return the equipment to working state, it is necessary to press the button of the same name. If at the same time the protection has worked again, you need to contact the specialists of the service department, because only they can eliminate the cause of the failure. If you do not intend to operate a water heater in the winter, it is likely that not only the appliance, but also the waterways will freeze. In order to eliminate this trouble, you must turn off the power and drain the water, only so you can avoid damage to the inner tank.

Connection to the water supply system

Water heater "Termex", connection of whichit is best to entrust specialists (only in this case will be covered by the guarantee for the equipment), should be mounted in several stages. Initially, a safety valve is installed at the inlet of cold water. It is important to ensure the tightness of the connection, to use an insulating material by the type of FSM tape. The manufacturer prohibits the use of a water heater of this brand without a safety valve or operate it in tandem with valves from other companies.

In the process of using the describedThe water heater can observe the appearance of droplets that leak from the drainage valve beak. This may be due to excessive pressure when heated. Users are advised to attach a silicone or rubber tube to the drainage beak, which will ensure the removal of moisture. The diagram of the water heater "Termex" is presented in the article, it should help you if you need to connect the equipment to the water supply system. The master should remember that the cold water inlet should be located below the hot water intake. Use in the process of this you need plastic, copper or plastic pipes. It will help with these manipulations flexible plumbing.

To the water heater it is recommended to supply the coolant after the mud, which should be on the cold water line.

Additional recommendations for connecting

Once the storage water heatersElectric "Termex" are connected, the cold water supply valve can be opened, this also applies to the hot water tap on the mixer. So you can ensure the outflow of air from the device. When cold water flows with a continuous stream from the faucet tap, this will indicate that the filling of the water heater has already been completed. If the device is installed in the place where the water supply is not connected, cold water can be supplied from the auxiliary tank. However, it is necessary to place it at a height of 5 meters from the top of the device. If this is not possible, it is additionally permissible to use a pumping station.

Note

Today,storage electric water heaters. Termex's comments are positive. These devices can be operated and by a more simple principle. For this purpose it is recommended to mount a drain valve. This applies to those models that do not have a spout in the kit. If it is necessary to install a water heater in a system where the pressure is higher than the above, the gearbox must be located at the entrance to the equipment, which must be purchased additionally. With it, you can reduce the water pressure to a nominal level.

Recommendations for maintenance

It is important to remember that due to poor qualitywater on the surface of the heater can form scale, which will certainly cause damage to the elements. This case is not covered by the warranty. In order to carry out maintenance, you will need to perform a number of actions. Among them, it is necessary to isolate the connection of the water heater from the mains, block the intake of cold water, and also to remove the safety valve.